About Hot Grips
Hot Grips On Line About Hot Grips
Replacement Parts Hot Grip Reviews
Hot Grip Frequently Asked Questions Hot Grip Support
Our Policies Contact Us at Hot Grips
Hot Grips On line Store
Made in the USA
Made in the USA
Since 1980
USA Shipments ONLY
No Canada Shipments
 


Please go to www.Amazon.com to search for the model kit you need.
Kits are in stock now and can ship immediately

Jim Hollander
www.hotgrips.com

Model Yamaha 88T-Red - Kit
Model Yamaha 88T-Red - Kit

Model 601-881 can be installed on Yamaha snowmobiles that require a grip interior length of 4.35" AND has an 18 volt power source feeding 9 volts to each grip.  Grips are wired in "series".  Check with your Yamaha snowmobile dealer.  WARNING:  From 1985 thru 2008 Yamaha used at least 11 different heated grip part numbers.  The key is to have the overall length, the interior length, and the voltage in order to determine if one of our Yamaha models will work for you.

 Hi-temp epoxy rated at 250 F required (not included)

Yamaha wires their two grips in "series" which means their 18 volt power source is fed into one grip and then the other grip before completing to negative ground. So each grip is going to be running off 50% of that voltage,i.e. 9 volts. If any of our Yamaha heated grips are used on a non-Yamaha snowmobile (Arctic Cat, Ski-Doo, Polaris) then they will not get as hot because the available voltage (12 volts divided by two = 6 volts per grip so output would be too little on high heat @ 12 watts per grip). You cannot run the Yamaha Hot Grips in "parallel" with a 12 volt source because then they would get so hot that they would melt. You CANNOT run them at 12 volts per grip. That would result in 48w per grip, far too much heat. With a Yamaha 18v power source, when properly wired in "series", each grip gets 9 volts. 9x9=81 then divided by 3 = 27 watts per grip. And that is a very -very hot hand warmer. You cannot leave them on high heat for very long, because your hands will be uncomfortable from so much wattage. Our Variable Heat Controller is designed to run on 12 volts, therefore you cannot use our Variable Heat Controller with the Yamaha grips.  All Yamaha heated grips are approximately 3.0 ohms resistance whereas all other snowmobile grips (except model 123) are approximately 2.4 ohms.  The Ohm's Law formula is:  Volts squared divided by ohms equals watts. 

 Available with OPEN ENDS on request, at no extra charge.

NOT for aluminum handlebars, as the aluminum acts like a heat sink, drawing away much of the heat.  Filling aluminum handlebars with ANY form of insulation is virtually ineffective.

If you want to see what the stock toggle switch looks like click on this link:  http://www.hotgrips.com/store.php?crn=204&rn=163&action=show_detail

To find more information about each available accessory for this product visit our the Accessory Summary page.


Buy Today!
Price: $87.95

required field Grips End Style:
Accessory:2-part Epoxy: (+ $7.25)
Enter The Make (Example - Suzuki):
Enter The Model (Example - DR650):
Enter The Year (Example - 2007):
required field indicates a required field.
Quantity:


 

| On-Line Store |
| About Us | Related Links | Reviews | FAQ | Support | Our Policy | Legal | Contact Us | Home |

"Hot Grips" and the associated logo are the trademark or the registered trademark of Hot Grips Manufacturing, Inc. Hot Grips® products
are protected under one or more of the following US/Canadian patents: USA: 4,471,209; 4,937,429; 4,990,753; 7,091,450; Canada: 1,299,621

Copyright 1999-2012 Hot Grips® Mfg.. All rights reserved.
Designed by NH VT Computer Services, LLC. and Hosted by GlobeInt.com, Inc.