About Hot Grips
Hot Grips On Line About Hot Grips
Replacement Parts Hot Grip Reviews
Hot Grip Frequently Asked Questions Hot Grip Support
Our Policies Contact Us at Hot Grips
Hot Grips On line Store
Made in the USA
Made in the USA
Since 1980
USA Shipments ONLY
No Canada Shipments
 

Model 575-875 - kit - for 7/8" Handlebars
Model 575-875 - kit - for 7/8" Handlebars

Our longest heated grip,  designed with the Honda Goldwing in mind. IMPORTANT: PLEASE READ THIS WARNING: IMPORTANT: Please email Jim@hotgrips.com before ordering, as there are different diameter throttle tubes which have caused problems and concerns for Honda Gold Wing purchasers. In brief some throttle tubes from Honda are 1.000" and some have been reported as 1.050" and even one as large as 1.080" diameter. While you can file down the throttle tube diameter to fit our grip's inside diameter, you CANNOT enlarge the interior of our grip so easily. In fact even with our methods it is extremely difficult and time consuming because our grip interior consists of many grooves which will violently catch attempts to "ream" it larger. We have developed a technique of using a 3-jaw chuck on a lathe and opening it up a little with a special boring bar cutter, then using a 400 degree F. heated aluminum bar to melt it out to 1.050" if absolutely required by a particular customer. It leaves a mess inside the grip interior of melted polymer but it does enlarge it. Not a DIY job in my opinion.

Many other riders, looking for a bit more grip width,  are also selecting this grip and we do maintain the same "watt-density" per square inch of exposed grip area regardless of which length grips you order..

Features our patented "burn-out proof" heating elements. We use .022" to .025" diameter furnace wire- depending on the watt-density we need for a particular grip length. It is designed to withstand being red-hot in service for other products, so we are not manufacturing a product that will burn out like a printed circuit. We use a minimum of 72" of wire in each grip, and it does not have unheated areas like the Chinese heated grips.

This "Comfort-Sized" grip naturally reduces wrist and hand stress.

Our unique Heat Isolation Ribs reduce heat transfer to the handlebars and keep the heat where it is needed - the rider's hands. IMPORTANT: PLEASE READ THIS WARNING: IMPORTANT: Please email Jim@hotgrips.com before ordering, as there are different diameter throttle tubes which have caused problems and concerns for Honda Gold Wing purchasers. In brief some throttle tubes from Honda are 1.000" and some have been reported as 1.050" and even one as large as 1.080" diameter. While you can file down the throttle tube diameter to fit our grip's inside diameter, you CANNOT enlarge the interior of our grip so easily. In fact even with our methods it is extremely difficult and time consuming because our grip interior consists of many grooves which will violently catch attempts to "ream" it larger.

 Dual Heat is standard with all our grips providing high heat, low heat or no heat.  Other options, including variable heat, are available.  

If you want to see what the stock toggle switch looks like click on this link:  http://www.hotgrips.com/store.php?crn=204&rn=163&action=show_detail

 A Variable Heat Controller can be installed and also makes wiring a set of grips super easy. See our controller by clicking on accessories.

Available with Open Ends so you can retain the end weights used on most modern bikes.  To have us bore out your grip ends, when you select this kit there is a drop-down menu where you check the line for Open Ends, which is done at no charge.   You can also select that you want either Honda stepped spacers or flat generic spacers.  Read more for further explanation of spacers.  Spacers are used at the end of the handlebars WHEN you purchase a kit with open ends AND select a grip length that is longer than stock.  The purpose of the spacers is to eliminate any friction on the end of your throttle tube when refitting your handlebar end-weights.   If you have a Honda and need open ended grips you may need stepped spacers as described:  http://www.hotgrips.com/store.php?crn=201&rn=380&action=show_detail  If you have any brand other than Honda and require open ended grips go to:  http://www.hotgrips.com/store.php?crn=201&rn=382&action=show_detail

 (1800cc Gold Wings need open-ended grips. IMPORTANT: PLEASE READ THIS WARNING: IMPORTANT: Please email Jim@hotgrips.com before ordering, as there are different diameter throttle tubes which have caused problems and concerns for Honda Gold Wing purchasers. In brief some throttle tubes from Honda are 1.000" and some have been reported as 1.050" and even one as large as 1.080" diameter. While you can file down the throttle tube diameter to fit our grip's inside diameter, you CANNOT enlarge the interior of our grip so easily. In fact even with our methods it is extremely difficult and time consuming because our grip interior consists of many grooves which will violently catch attempts to "ream" it larger.)

To look at Installation Instructions click here:http://hotgrips.com/pdfs/moto-inst.pdf

 CUSTOM OPTIONS - all our grips come stock with a high/low/off toggle switch. However you can select a variable heat controller, mini toggle switch or handlebar mounted switch as options.

Technical Specifications

Voltage:
12.0 - 14.6 volts
Amps/Watts: approx 3.0 amps
Handlebar Diameter: 7/8"
Outside Diameter: 1.440"
Inside Diameter: Left ID = .875" and right = 1.000"
External length: 5 3/4"
Internal length: 5.450" if unmodified, and 5.750" if bored out
Includes: Pair of Grips, three position toggle switch, extra wire, resistor for low heatand detailed instructions
Wiring Method: Parallel
Required Adhesive: Epoxy rated for 250 F. (not included)
Available Options: Handlebar mounted switch, mini switch, variable heat controller

 

To find more information about each available accessory for this product visit our the Accessory Summary page.


Buy Today!
Price: $124.95

required field Grips End Style:
Accessory: Variable Heat Controller-2: (+ $41.95)
Accessory:2-part Epoxy: (+ $7.25)
Accessory: Fuse Holder with 6amp fuse : (+ $3.25)
Enter The Make (Example - Suzuki):
Enter The Model (Example - DR650):
Enter The Year (Example - 2007):
Enter The Engine Size (Example - 125cc):
required field indicates a required field.
Quantity:


 

| On-Line Store |
| About Us | Related Links | Reviews | FAQ | Support | Our Policy | Legal | Contact Us | Home |

"Hot Grips" and the associated logo are the trademark or the registered trademark of Hot Grips Manufacturing, Inc. Hot Grips® products
are protected under one or more of the following US/Canadian patents: USA: 4,471,209; 4,937,429; 4,990,753; 7,091,450; Canada: 1,299,621

Copyright 1999-2012 Hot Grips® Mfg.. All rights reserved.
Designed by NH VT Computer Services, LLC. and Hosted by GlobeInt.com, Inc.