About Hot Grips
Hot Grips On Line About Hot Grips
Replacement Parts Hot Grip Reviews
Hot Grip Frequently Asked Questions Hot Grip Support
Our Policies Contact Us at Hot Grips
Hot Grips On line Store
Made in the USA
Made in the USA
Since 1980
USA Shipments ONLY
No Canada Shipments
 

Model 475-100 - kit - for 1" Handlebars
Model 475-100 - kit - for 1" Handlebars

A Perfect fit for most Harley Davidsons (1982 - 2011)

If you have one of the very latest Harley Davidson's with the electronic throttle (wire throttle instead of cable throttle) as shown at the bottom of the following webpage: http://www.sideroadcycles.com/ImportedMotorcycles/ImportHandlebars/ImportHandlebars.html then be aware that installation may be difficult due to the complexity of the throttle mechanism.  We have had reports of some customers being successful but we do not encourage it by any means.  The technique is to place the epoxy on the throttle tube ONLY inboard of the end gear mechanism, and when you slide the heated grip into position, DO NOT pull the grip outward or you will contaminate the throttle gear mechanism with epoxy.   If you purchase our heated grips for this application, attempt to install them and are unsuccessful, we cannot take back the grips with epoxy inside them or with obvious handling marks, as we cannot repackage and re-sell them.  See the photos at that webpage link to understand why.

If you want chromed polymer end caps ( need pre-fitting before we ship) click here for more information-  http://www.hotgrips.com/store.php?crn=201&rn=381&action=show_detail

This grip also fits many Japanese Cruisers with 1" handlebar diameter and 1-1/8" throttle tube.

 Our unique internal Heat Isolation Ribs naturally limit heat transfer to the handlebars and put heat where it is needed - the rider's hands.

 Patented Heating Elements are "burn-out" proof, we use .025" dia. wire.

 Comfort-Sized grips naturally reduce wrist and hand stress.

 High heat, Low heat , or Off  is provided with all our grips.  If you want to see what the stock toggle switch looks like click on this link:  http://www.hotgrips.com/store.php?crn=204&rn=163&action=show_detail

Available with Open Ends: (rarely needed on this diameter handlebar) so you can retain the end weights used on most modern sport bikes.  To have us bore out your grip ends, when you select this kit there is a drop-down menu where you check the line for Open Ends.   You can also select that you want either Honda stepped spacers or flat generic spacers.  Read more for further explanation of spacers.  Spacers are used at the end of the handlebars WHEN you purchase a kit with open ends AND select a grip length that is longer than stock.  The purpose of the spacers is to eliminate any friction on the end of your throttle tube when refitting your handlebar end-weights.   If you have a Honda and need open ended grips you may need stepped spacers as described:  http://www.hotgrips.com/store.php?crn=201&rn=380&action=show_detail  If you have any brand other than Honda and require open ended grips go to:  http://www.hotgrips.com/store.php?crn=201&rn=382&action=show_detail

CUSTOM OPTIONS. All our grips come stock with a three position toggle switch allowing you to select high or low or no heat.  Available Options include a handlebar mounted switch, mini switch or infinitely variable heat controller.  When the variable heat controller is ordered you will not use the standard toggle switch and resistor, but they're left in the kit if for some reason you elect to use them instead of the electronic controller.

To look at Installation Instructions click here:http://hotgrips.com/pdfs/moto-inst.pdf

Technical Specifications

Voltage:
12.0 - 14.6 volts
Amps/Watts: 3.0 amps/ 30 watts @ 12vdc
Handlebar Diameter: 1"
Outside Diameter: 1.440"
Inside Diameter: Left ID = 1.000" and right = 1.130"
External length: 4 3/4"
Internal length: 4.450"
Includes: Pair of Grips, three position toggle switch, extra wire, resistor for low heat and detailed instructions
Wiring Method: Parallel
Required Adhesive: Epoxy rated for 250 F. (not included with the kit, but available under Accessories)
Available Options: Handlebar mounted switch housing, mini switch, variable heat controller, epoxy.

To find more information about each available accessory for this product visit our the Accessory Summary page.


Buy Today!
Price: $122.95

required field Grips End Style:
Accessory: Variable Heat Controller-2: (+ $41.95)
Accessory: Switch housing - no switch: (+ $14.95)
Accessory:2-part Epoxy: (+ $7.25)
Accessory: Fuse Holder with 6amp fuse : (+ $3.25)
Enter The Make (Example - Suzuki):
Enter The Model (Example - DR650):
Enter The Year (Example - 2007):
Enter The Engine Size (Example - 125cc):
required field indicates a required field.
Quantity:


 

| On-Line Store |
| About Us | Related Links | Reviews | FAQ | Support | Our Policy | Legal | Contact Us | Home |

"Hot Grips" and the associated logo are the trademark or the registered trademark of Hot Grips Manufacturing, Inc. Hot Grips® products
are protected under one or more of the following US/Canadian patents: USA: 4,471,209; 4,937,429; 4,990,753; 7,091,450; Canada: 1,299,621

Copyright 1999-2012 Hot Grips® Mfg.. All rights reserved.
Designed by NH VT Computer Services, LLC. and Hosted by GlobeInt.com, Inc.